slidetec WATER s

The SLEE tissue floating bath slidetec WATER s is a special bath for histological, pathological, clinical and bacteriological laboratories for stretching and drying cut tissue samples.

The outer housing is made of powder-coated aluminum sheet, the bath body and the edges of the bath body for drying the raised tissue sections of black anodized aluminum sheet.

The devices can be controlled via an electromechanical temperature controller with capillary tube sensor in the temperature range from 5 ° C above room temperature to approx. 80 ° C and are protected by a temperature fuse during dry running. The bath is heated indirectly, plate radiator, sensor of the thermostat and temperature fuse are under the bath body.

Highlights

  • Safe and ergonomic work is possible
  • The control thermometer is easy to read
  • Appealing design
  • Easy to operate and clean
  • Small footprint of only 280 Ø mm

Specifications

  • Exterior dimensions (diameter / height) 280 mm / 100 mm
  • Interior dimensions (diameter / height) 200 mm / 60 mm
  • Usable bath height 50 mm
  • max. filling quantity (in liters) 1.6 l
  • Temperature range approx. 5 °C above ambient to +80°C
  • Temperature control capillary thermostat
  • Temperature setting on the turning knob
  • Temperature constancy, temporal approx. +/- 0.5
  • Over-temperature cut-out Temperature cut-out, >130°C
  • Electrical connection non-resettable
  • Power 150 – 240 V /50-60 Hz, 115 V / 60 Hz
  • Mains connection shock-proof plug
  • Mains fuse min. 10 A – max. 16 A
  • Protection type / protection class IP20/I
  • Ambient conditions use only indoors (not in potentially explosive surroundings)
  • Height above sea level p to 2.000 m NN
  • Ambient temperature + 10°C to +40°C
  • Humidity max. 80 % relative humidity up to 31°C
  • Weight 2 kg

slidetec WATER s

The SLEE tissue floating bath slidetec WATER s is a special bath for histological, pathological, clinical and bacteriological laboratories for stretching and drying cut tissue samples.

The outer housing is made of powder-coated aluminum sheet, the bath body and the edges of the bath body for drying the raised tissue sections of black anodized aluminum sheet.

The devices can be controlled via an electromechanical temperature controller with capillary tube sensor in the temperature range from 5 ° C above room temperature to approx. 80 ° C and are protected by a temperature fuse during dry running. The bath is heated indirectly, plate radiator, sensor of the thermostat and temperature fuse are under the bath body.

Highlights

  • Safe and ergonomic work is possible
  • The control thermometer is easy to read
  • Appealing design
  • Easy to operate and clean
  • Small footprint of only 280 Ø mm

Specifications

  • Exterior dimensions (diameter / height) 280 mm / 100 mm
  • Interior dimensions (diameter / height) 200 mm / 60 mm
  • Usable bath height 50 mm
  • max. filling quantity (in liters) 1.6 l
  • Temperature range approx. 5 °C above ambient to +80°C
  • Temperature control capillary thermostat
  • Temperature setting on the turning knob
  • Temperature constancy, temporal approx. +/- 0.5
  • Over-temperature cut-out Temperature cut-out, >130°C
  • Electrical connection non-resettable
  • Power 150 – 240 V /50-60 Hz, 115 V / 60 Hz
  • Mains connection shock-proof plug
  • Mains fuse min. 10 A – max. 16 A
  • Protection type / protection class IP20/I
  • Ambient conditions use only indoors (not in potentially explosive surroundings)
  • Height above sea level p to 2.000 m NN
  • Ambient temperature + 10°C to +40°C
  • Humidity max. 80 % relative humidity up to 31°C
  • Weight 2 kg